Working Principle of Pneumatic Globe Valvevalves in oil and gas

butterfly valves in texas

butterfly valves manufacturers in texas

flowserve texas butterfly valve

Table of Contents

  • 1. Introduction of pneumatic globe valve
  • 2. Introduction to the working principle of pneumatic globe valve 

1. Introduction of pneumatic globe valve

Pneumatic cut-off valve, widely used in the important system of mine and nuclear power plant, is an important key equipment to ensure the safety production of power plant. In the actual operation, many factors such as the setting of manual mechanism, packing failure, improper operation, insufficient air intake flow lead to many failures, which threaten the safe and stable operation of the power station. In this article, taking the pneumatic globe valve produced by SEREG as an example, analyze the working principle of typical pneumatic globe valve for power station, and describe the setting of neutral point in detail. It provides a basis for the operation and troubleshooting of SEREG pneumatic globe valve or similar pneumatic globe valve used in the power station.

2. Introduction to the working principle of pneumatic globe valve 

Working principle of pneumatic globe valve: most of the valves which uses compressed air as power source adopt remote control. The main control room manually or automatically triggers the action command to make the intake and exhaust solenoid valve act to supply and exhaust compressed air to the actuator. Compressed air acts on the piston or diaphragm to overcome the friction of valve action and the spring force on the stem. Press down (Loss of air pressure, open the valve J ) or lift up (Loss of air pressure, open the valve F1) the valve rod, driving the valve core up and down to open or close the valve. When the air pressure is lost in the valve and the driving head compresses air, the valve will be in the safe position of full opening or full closing according to the requirements of the system. The air supply pressure of the service instrument is generally 4-9 bar. Before entering the valve, filter and purify the compressed air through the filter, and then reduce the pressure through the pressure reducing valve. The reading of the inlet pressure gauge is not more than 4bar. The adjustment can be realized by adjusting the adjusting screw installed on the top of the pressure reducing valve, and the protective cover shall be loosened before adjustment.

The four most common and widely used types of pneumatic globe valves are: the valve closed by air loss of handwheel, the valve opened by air loss of handwheel, the valve closed by air loss without handwheel, and the valve opened by air loss without handwheel.

ZECO Valve

NBR Butterfly Valve

Gate Valve Repair

Gate Valve vs Ball Valve

What is a Globe Valve?

What is an Axial Check Valve

What are Globe Valves?

Manual Operate Gate Valve Manufacturer

Difference Between Gate Valve And Butterfly Valve

What is a Gate Valve?

Shanghai Pressure Reducing Valve Factory

Similar Posts

Swing Check Valve 6inch 1500LB Bolted Bonnet

Byroot

Key Specifications / Features Model No.: X47W Hits: 44 China Plug Valve Manufacturer Jonloo supplies Inverted Pressure Balance Lubricated Plug Valve. It is applicable to various industries such as petroleum, chemical industry, pharmacy, chemical fertilizer, power industry, etc. The Application of Swing Check Valve Cameron, a renowned manufacturer of industrial valves, offers a diverse range…

Introduction Of EPDM & NBR Butterfly Valve Seat – Zeco Valvebellow seal valve

ByBrina

ZECO butterfly valves are usually classified as butterfly CI, butterfly WCB, butterfly bronze, and butterfly stainless steel. Butterfly valves are available in sizes from 2 inch to 8 inch usually using handle operation, above 8 inch butterfly valves the torque on the rubber seat increases usually starting with turbo, pneumatic or electric operation. Table of Contents What is a butterfly valve…

Hastelloy Valves in Aerospace: Meeting the Demands of Extreme Environments

Byroot

ls valve spring compressor ls1 valve covers inspect the cooling tower valve seats modulating control valve Aerospace applications are among the most demanding in engineering. The materials and components used in aerospace must perform flawlessly in extreme conditions, where temperature variations, high pressures, and corrosive environments are the norm. In this blog, we will explore…

Bronze Flanged Gate Valve

Byroot

The Application of Bronze Flanged Gate Valve The application of Bronze Flanged Gate Valve in industrial settings is essential for efficient flow control. Renowned Bronze gate valve suppliers like Cameron offer top-quality products that ensure reliability and durability. For optimal performance, following Bronze valve maintenance tips is crucial. Choosing the right Bronze gate valve suppliers…

Non-lubricated Plug Valve 2 inch 300 LB A216 WCB PTFE Sleeve API 599

Byroot

The Application of Non-lubricated Plug Valve Non-lubricated Plug Valves offer a reliable and low-maintenance solution for flow control applications where lubricated valves may not be suitable. Unlike lubricated plug valves, which require periodic lubrication, non-lubricated versions rely on the inherent properties of the materials used in their construction to provide a smooth and efficient operation. This makes them an ideal choice…

Subsea Ball Valve

Byroot

Subsea Ball Valve is engineered for high-integrity sealing and trouble-free operation in a wide range of harsh subsea service environments. The Applications of Subsea Ball Valve Subsea ball valves are designed to operate reliably in deep, offshore environments. They are commonly used in subsea oil and gas production systems to provide isolation and flow control….